ReaXcomp
From CockosWiki
(Difference between revisions)
m |
|||
| Line 1: | Line 1: | ||
| - | [[ | + | [[Main_Page|Main Page]] > [[Reaper_Documentation|REAPER Documentation]] > [[ReaperEffects|REAPER Effects]] |
| - | ''' | + | |
| + | |||
| + | [[Image:ReaXcomp.PNG]] | ||
| + | |||
| + | Standard Display | ||
| + | |||
| + | [[Image:ReaXcomp-NoTabs.PNG]] | ||
| + | |||
| + | Display without Tabs or Grid | ||
| + | |||
| + | ReaXcomp is a compressor plug-in. | ||
| + | |||
| + | =Controls= | ||
| + | {{EffectsControlsCommon}} | ||
| + | |||
| + | The basic controls of ReaComp are: | ||
| + | |||
| + | *'''Active''' - Enables or disables the current tab | ||
| + | *'''Threshold''' - Lower the threhsold to catch peaks, or delve deep into the innards of an audio signal. | ||
| + | *'''Ratio''' - From 1:1 to 100:1 (inf), the higher the ratio, the more marked the effect | ||
| + | *'''Auto make-up gain''' - Increases the gain when it drops below the threshold | ||
| + | *'''Program dependant release''' - ?? | ||
| + | *'''Feedback detector''' - ?? | ||
| + | *'''Knee Size''' - From 0dB to 24dB - This will tell the compressor to either start compressing as soon as a signal goes over the threshold (0dB) or start compressing after it goes over the threshold by a pre-determined amount (i.e. 1db to 24dB). | ||
| + | *'''Attack''' - From 0ms to 500ms (0.5 seconds) The time it take for the compression effect to reach full compression | ||
| + | *'''Release''' - From 0ms to 5000ms (5 seconds) The time it take for the compression effect to reach zero compression | ||
| + | *'''RMS size''' - This is an RMS detection function - generally, setting this value low gives more compression, and less compression when set higher. | ||
| + | *'''Log() scale automated frequencies''' | ||
| + | *'''Gain''' - The Gain for this tab | ||
| + | *'''Gain''' - The overall Gain for the plugin | ||
| + | *'''Add Band''' - Adds a band (tab) | ||
| + | *'''Delete Band''' - Deletes a band (tab) | ||
| + | *'''Rest to defaults''' - | ||
| + | *'''Solo current band (tab)''' - | ||
| + | *'''Tabs''' - Toggle the display of tabs | ||
| + | *'''Grid''' - Toggle the display of the grid | ||
| + | |||
| + | [[Main_Page|Main Page]] > [[Reaper_Documentation|REAPER Documentation]] > [[ReaperEffects|REAPER Effects]] | ||
| + | |||
| + | [[Category:REAPER]] [[Category:ReaComp]] | ||
Revision as of 18:01, 11 January 2010
Main Page > REAPER Documentation > REAPER Effects
Standard Display
Display without Tabs or Grid
ReaXcomp is a compressor plug-in.
Controls
Common Controls
Move a fader to set a value or, to set a value precisely, type directly into the input box if it is not "greyed-out". Double Click a fader to return to its default value.
"Fine-tune" a value controlled by a fader by holding the Ctrl key while moving the fader.
- Drop-down list -
- + - Patch and Patch/MIDI program change link management, displays a graphic similar to this:
- Param
- 2 in 2 out - Routing. The plugin pin connector, displays a graphic similar to this:
Extra channels can be created by clicking on the +
- UI - Toggle between default and custom User Interface
- 100% Wet - The plugin is bypassed when this is checked
Plugin Specific Controls
The basic controls of ReaComp are:
- Active - Enables or disables the current tab
- Threshold - Lower the threhsold to catch peaks, or delve deep into the innards of an audio signal.
- Ratio - From 1:1 to 100:1 (inf), the higher the ratio, the more marked the effect
- Auto make-up gain - Increases the gain when it drops below the threshold
- Program dependant release - ??
- Feedback detector - ??
- Knee Size - From 0dB to 24dB - This will tell the compressor to either start compressing as soon as a signal goes over the threshold (0dB) or start compressing after it goes over the threshold by a pre-determined amount (i.e. 1db to 24dB).
- Attack - From 0ms to 500ms (0.5 seconds) The time it take for the compression effect to reach full compression
- Release - From 0ms to 5000ms (5 seconds) The time it take for the compression effect to reach zero compression
- RMS size - This is an RMS detection function - generally, setting this value low gives more compression, and less compression when set higher.
- Log() scale automated frequencies
- Gain - The Gain for this tab
- Gain - The overall Gain for the plugin
- Add Band - Adds a band (tab)
- Delete Band - Deletes a band (tab)
- Rest to defaults -
- Solo current band (tab) -
- Tabs - Toggle the display of tabs
- Grid - Toggle the display of the grid
